East Coast Part Supplier and Warehouse Association Moderated Interchange Newsgroup > Mass.
> Machinery
> Horizontal,wall-mounted baby changing station KB100-01
Horizontal,wall-mounted baby changing station KB100-01
Koala Standard Horizontal Baby Changing Station
FDA approved blow-molded high-density polyethylene. Reinforced full-length steel-on-steel
hinge mechanism, with 11-gauge steel mounting plates and mounting hardware included.
Molded in graphics and safety messages in six languages and Braille. Contoured changing
surface area is 442 sq in (2873 sq mm) and comes complete with nylon safety straps and
Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and
closing of bed. High-density polyethylene is easy to clean and resists odors and bacterial
growth. Complies with ASTM static load performance requirements when properly installed.
Rated to support a static load of 300 pounds (136 kilos); tested to 400 pounds (182 kilos).
Molded-in liner dispenser holds approximately 25 KB150-99 sanitary liners.
To insure that the unit supports the intended loads, baby changing stations must
be properly installed according to the manufacturer’s instructions.
To insure proper installation and compliance to building codes, it is recommended that a
qualified person or carpenter perform the installation of the unit. Koala Bear Kare® Baby
Changing Stations have been tested to hold a static load of up to 400 pounds. To do this,
the unit must be properly installed onto a permanent wall that is capable of supporting that
much weight and can accommodate the supplied installation hardware. The Koala Bear
Kare® Baby Changing Station meets ADA regulations when properly installed. Refer to
Federal Register, Volume 56, No. 144 28 CFR Part 36.
Drilling holes and mounting the station:
Identify the best location for installing the baby changing station. Hold the unit in
place, open the bed, and make sure that there is adequate operating clearance.
2. Based upon the type of wall on which the unit will be mounted, determine the best
method of mounting. Not all of included hardware may be required for proper
3. The horizontal unit has four mounting holes provided in the back wall of the unit,
which are positioned on a 32†stud center. If possible, locate the wood or metal wall
studs for fastening the changing station in the desired location. If the walls do not
have studs on the center as outlined, make sure at least one side of the unit is
installed into the stud. Use toggles (supplied) for holes on the other side.
4. Find the stud where you will be attaching the left side of the changing station to the
wall. Measure 48†up from the floor (44†ADA), at the center of the stud, and mark
the wall. Line up the top left mounting hole with this mark, then use a measuring
tape and level to mark the remaining three mounting holes. This will locate the
bottom of the station 30-1/2†from the floor (26-1/2†ADA).
If the wall has wood studs on 16†or 32†centers, drill 1/8†pilot holes at the marks and use
the four ¼†x 3†panhead tapping screws with supplied washers. If the wall is masonry or tile
over wood studs, use a 7/32†masonry drill until you hit the stud, then proceed to drill 1/8â€
The illustrations and descriptions herein are applicable to production as of the date of this technical data sheet.
The manufacturer reserves the right to make changes and improvements in designs and dimensions without notice.
KB100-00/01/05 Revised 08/2004 © 2004 by Koala Kare Products, A Division of Bobrick Printed in USA
pilot holes into the studs and use the four 1/4†x 3†panhead tapping screws with supplied
If the wall has wood studs that are not on 16†or 32†centers, has metal studs, or an
underlying surface of concrete block, drill with a ½†masonry bit. A minimum of 2-1/2†of
inside wall space is required for toggles to turn. Insert supplied toggles and tighten, locate
station over toggles, then use supplied ¼†x 3†Phillips Panhead machine screws with
Baby changing station body shall be durable, high-impact polyethylene. Design of unit shall
be surface-mounted. Unit shall be equipped with a pneumatic cylinder for controlled
opening and closing of bed. Bed shall be secured to back plate with a concealed, full-length
steel-on-steel hinge. No hinge structure shall be exposed on interior or exterior surfaces.
Unit shall have 11-gauge steel mounting plates with mounting hardware included. Unit shall
conform to ANSI S117.1, ASTM PS 125 (federal regulation compliance, load support, pinch
points, child restraint), ANSI Z535.4, R-0367 German TUV or local code if more stringent
installation requirements are applicable for handicapped accessibility. Unit shall comply with
ADA regulations when properly installed. Bed shall have smooth concave changing area
with a nylon safety strap and two hooks for bags or purses. Unit shall have a built-in Liner
Dispenser for use with 3-ply chemical free biodegradable sanitary liners, universal
instruction graphics and safety messages in 6 languages. Manufacturer’s service and parts
manual shall be provided to the building owner/manager upon completion of project. Unit
5-year replacement warranty against vandalism. Unit shall be manufactured in the U.S.A.
KOALA KARE HORIZONTAL,WALL-MOUNTED BABY CHANGING STATION KB100-01
FDA approved blow-molded high-density polyethylene. Reinforced full-length steel-on-steel
hinge mechanism, with 11-gauge steel mounting plates and mounting hardware included.
Molded in graphics and safety messages in six languages and Braille. Contoured changing
surface area is 442 sq in (2873 sq mm) and comes complete with nylon safety straps and
Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and
closing of bed. High-density polyethylene is easy to clean and resists odors and bacterial
growth. Complies with ASTM static load performance requirements when properly installed.
Rated to support a static load of 300 pounds (136 kilos); tested to 400 pounds (182 kilos).
Molded-in liner dispenser holds approximately 25 KB150-99 sanitary liners.
To insure that the unit supports the intended loads, baby changing stations must
be properly installed according to the manufacturer’s instructions.
To insure proper installation and compliance to building codes, it is recommended that a
qualified person or carpenter perform the installation of the unit. Koala Bear Kare® Baby
Changing Stations have been tested to hold a static load of up to 400 pounds. To do this,
the unit must be properly installed onto a permanent wall that is capable of supporting that
much weight and can accommodate the supplied installation hardware. The Koala Bear
Kare® Baby Changing Station meets ADA regulations when properly installed. Refer to
Federal Register, Volume 56, No. 144 28 CFR Part 36.
Drilling holes and mounting the station:
Identify the best location for installing the baby changing station. Hold the unit in
place, open the bed, and make sure that there is adequate operating clearance.
2. Based upon the type of wall on which the unit will be mounted, determine the best
method of mounting. Not all of included hardware may be required for proper
3. The horizontal unit has four mounting holes provided in the back wall of the unit,
which are positioned on a 32†stud center. If possible, locate the wood or metal wall
studs for fastening the changing station in the desired location. If the walls do not
have studs on the center as outlined, make sure at least one side of the unit is
installed into the stud. Use toggles (supplied) for holes on the other side.
4. Find the stud where you will be attaching the left side of the changing station to the
wall. Measure 48†up from the floor (44†ADA), at the center of the stud, and mark
the wall. Line up the top left mounting hole with this mark, then use a measuring
tape and level to mark the remaining three mounting holes. This will locate the
bottom of the station 30-1/2†from the floor (26-1/2†ADA).
If the wall has wood studs on 16†or 32†centers, drill 1/8†pilot holes at the marks and use
the four ¼†x 3†panhead tapping screws with supplied washers. If the wall is masonry or tile
over wood studs, use a 7/32†masonry drill until you hit the stud, then proceed to drill 1/8â€
The illustrations and descriptions herein are applicable to production as of the date of this technical data sheet.
The manufacturer reserves the right to make changes and improvements in designs and dimensions without notice.
KB100-00/01/05 Revised 08/2004 © 2004 by Koala Kare Products, A Division of Bobrick Printed in USA
pilot holes into the studs and use the four 1/4†x 3†panhead tapping screws with supplied
If the wall has wood studs that are not on 16†or 32†centers, has metal studs, or an
underlying surface of concrete block, drill with a ½†masonry bit. A minimum of 2-1/2†of
inside wall space is required for toggles to turn. Insert supplied toggles and tighten, locate
station over toggles, then use supplied ¼†x 3†Phillips Panhead machine screws with
Baby changing station body shall be durable, high-impact polyethylene. Design of unit shall
be surface-mounted. Unit shall be equipped with a pneumatic cylinder for controlled
opening and closing of bed. Bed shall be secured to back plate with a concealed, full-length
steel-on-steel hinge. No hinge structure shall be exposed on interior or exterior surfaces.
Unit shall have 11-gauge steel mounting plates with mounting hardware included. Unit shall
conform to ANSI S117.1, ASTM PS 125 (federal regulation compliance, load support, pinch
points, child restraint), ANSI Z535.4, R-0367 German TUV or local code if more stringent
installation requirements are applicable for handicapped accessibility. Unit shall comply with
ADA regulations when properly installed. Bed shall have smooth concave changing area
with a nylon safety strap and two hooks for bags or purses. Unit shall have a built-in Liner
Dispenser for use with 3-ply chemical free biodegradable sanitary liners, universal
instruction graphics and safety messages in 6 languages. Manufacturer’s service and parts
manual shall be provided to the building owner/manager upon completion of project. Unit
5-year replacement warranty against vandalism. Unit shall be manufactured in the U.S.A.
